(48)
Drive pins with a 0.300 diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.
(7)
The Powers PTZ Powder Actuated Fasteners are designed for fastening through pressure treated lumber into concrete and grout filled masonry The fasteners are manufactured to provide a minimum level of corrosion resistance equivalent to triple zinc coatings (G-185) found on connector hardware available for pressure treated lumber applications. The fasteners are available with either a round or square washer for increased pullover resistance.
(7)
Drive pins with an 8 mm and 10 mm diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.177/0.145" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A plastic washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.
(23)
The Pins listed below are used primarily for applications fastening drywall track to concrete or steel, They are assembled with a metal top hat to provide extra bearing surface against the drywall track. To provide resistance to pullover, these pins are available with preassembled 14 gage (0.075") metal washers in various diameters.
(12)
Drive pins with a 6 mm diameter head are designed for permanently fastening a fixture to concrete, some types of masonry, and A36 structural steel. The pins are manufactured with a 0.145" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A 12 mm metal washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.
(7)
Drive pins with a 3/8" diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. The pins are manufactured with a 0.171" diameter shank in various lengths. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.
(6) Power Point Drive-Type Fasteners Premium drive pins with a 0.300 diameter head have a specially designed point to allow more consistent penetration into harder base materials. Will reduce failures in dense concrete and steel. Drive Pins are manufactured with a 0.150" diameter shank in various lengths. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation.
"EIFS": Acronym for Exterior Insulation & Finish Systems EIF5 Pins with a 0.300 diameter read 1-1/2" length are designed for permanently fastening to concrete or concrete block, installation systems such as, waterproofing membranes, plastic sheeting, metal lathe and wire mesh for plaster and stucco systems.
To provide resistance to pullover, these pin are pre-assembled onto a soft plastic diaphragm. Resistance to pullover is increased by the additional bearing surfaces that is provided by the diaphragm.
(11)
Threaded studs are available in 1/4"-20 and 3/8"-16 thread diameters with a variety of thread and shank lengths for use in concrete, some types of masonry, and A36 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required. The shank diameter for the threaded stud is 0.145" for the 1/4"-20 diameter and 0.205" for the 3/8"-16 diameter. Knurled shank designs are available to increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. On the 1/4"-20 threaded studs, a plastic cap is also provided to protect the threads of the fastener ...
For concrete forming applications, the 1-3/4" (44mm) pin is designed for fastening wood members up to 3/4" in thickness while the 2-1/2" (62mm) pin is designed for wood members up to 1-1/2" in thickness. The pin has a break off groove 1" from te point to allow the wood forming members to be easily removed.
(8)
Hammer Drive® pins are designed for permanently fastening a fixture to concrete and some types of masonry. This fastener is designed for use in a standard hand tool and should not be used in a powder actuated tool. The pins are formed with a 1/4" diameter head on one end and a 0.140" diameter shank in various lengths. A 3/8" diameter steel washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. This fastener is recommended for light duty static load applications where holding power is not a critical factor. It should not be used overhead.